TECHNOLOGIES FOR PROCESSING WORKING PARTS OF DIES USED IN COLD VOLUME STAMPING
Keywords:
Abstract
This paper presents an analysis of the technical requirements for cold stamping, wear of their working zones, factors affecting wear and ways to increase wear resistance.
Similar Articles
-
Management Of Higher Education Institutions-As A Object Of Economic Diagnosis
The American Journal of Engineering and Technology: No. 10 (2021) / Boydadaev Davron Mahmudovich, -
SENIOR INTERIOR DESIGN STUDENTS’ PERCEPTIONS ABOUT DISTANCE LEARNING IN THE SHADOW OF COVID-19
The American Journal of Engineering and Technology: No. 05 (2024) / Arshad Saqqaf, -
The Possibilities Of Using Robotics Elements In Physics Lessons In Science
The American Journal of Engineering and Technology: No. 02 (2021) / O.A. Tuychiev, -
Developing Educational Technologies In School Technology Education
The American Journal of Engineering and Technology: No. 07 (2020) / M.Kh. Shomirzayev, -
Effect Of Problem-Based Learning Method On Students’ Academic Achievement In Computer Hardware Maintenance In Universities In Enugu State, Nigeria
The American Journal of Engineering and Technology: No. 11 (2021) / Ifeanyi John Eneovo, Theresa Chinyere Ogbuanya, -
The Use Of Artificial Intelligence Is Currently Relevant And The Reasons For This
The American Journal of Engineering and Technology: No. 05 (2021) / Izzatbek Po’latov Xislat O’g’li, Mashxurbek Muhiddinov Ikromjon O'g'li, Ibragimov Anvar Abdurahim O'g'li, -
Developing Educational Technologies In School Technology Education
The American Journal of Engineering and Technology: No. 07 (2020) / M.Kh. Shomirzayev, -
A COMPARATIVE ANALYSIS OF MODERN AND TRADITIONAL METHODS OF TEACHING ENGINEERING GRAPHICS
The American Journal of Engineering and Technology: No. 11 (2023) / Mashrapova Gulbakhor Mamasalievna, -
Results Of Studying The Physical And Mechanical Properties Of Polystyrene Concrete With Additional Complex Chemical Additive Kdj-3 Based On Local Raw Materials
The American Journal of Engineering and Technology: No. 06 (2021) / Mirzaev Bakhodir Kuziboevich, Abduganiev Numonjon Nabijonovich, -
Change Of Physical And Mechanical Properties Of Twisted Yarn During Rewinding
The American Journal of Engineering and Technology: No. 08 (2020) / Bobojanov Husankhon Tohirovich, Yusupov Alijon Abdujabbor O‘g‘Li,
References
Abdujalol, B., Nodir, T., Fakhriddin, M., Nuriddin, T., Kamola, T., & Nargiza, S. (2022). Development of steel wheel detail casting technology. Asian Journal of Multidimensional Research, 11(8), 82-88.
Alon Mishra, Joydeep Maity. Structure – property correlation of AlSi 1080 steel subjected to cyclic quenching treatment // Materials Science Engineering A. – 646. – 2015. – Р. 169-181.
Гурьев A.M., Земляков С.А. Новая высокоэффективная технология термического упрочнения режущего и штампового инструмента. В сб. трудов научно-технической конференции 5-7 апреля 2000 г.- Барнаул: Изд-во АлтГТУ, 2000.- С.25-27.
Марочник сталей и сплавов. М. М. Колосков, Е.Т. Долбенко, Ю.В. Каширский и др. Под ред. А. С. Зубченко – М.: Машиностроение, 2001.- 672 С.
Фирсова Н. В. Разработка оптимального легирующего комплекса и режимов термического упрочнения штамповых сталей. Дисс. на соиск. уч. степ, к.т.н. / Н.В. Фирсова. -Оренбург, 2011. - 17 с.
Norkhudjayev, F. R., Mukhamedov, A. A., Khudayberdiev, O. R., Ergashev, D. M., & Norkhudjayeva, R. F. (2020). Development of Machine-Building Materials and Details of Machines from the Powders received from Waste of Raw Materials in the Industry of Uzbekistan. Test Engineering and Management, 83(5-6), 639-646.
Norkhudjayev, F. R., Mukhamedov, A. A., Djalolova, S. T., Ergashev, D. M., & Hudayberdiyev, O. R. (2020). Technological capabilities of application of thermocyclic processing (Tcp) tool steel. International Journal of Psychosocial Rehabilitation, 24(8), 1866-1874.
Норхуджаев, Ф. Р., Мухамедов, А. А., Эргашев, Д. М., Норхужаева, Р. Ф., & Тешабоев, А. М. (2021). Влияние режимов термоциклическая обработка на структурообразование инструменталъных сталях. Композиционные материалы, 1, 75-77.
Норхуджаев, Ф. Р., Эргашев, Д. М., & Тешабоев, А. М. (2021). Упрочненение режущих сегментов аппаратов уборочных машин. Композиционные материалы, 2, 92
Ataxonova, S. Q., & Mo’Ydinova, D. R. (2022). METALL QOTISHMALARINING MARKALANISHI TAHLILI. Oriental renaissance: Innovative, educational, natural and social sciences, 2(3), 312-326.
Ataxonova, S. Q., & Murodjon o'g, S. U. B. (2022). Analysis Of Magnetic Materilas. Texas Journal of Multidisciplinary Studies, 6, 23-26.
Ataxonova, S. Q. (2021). METALLARNI SIFAT NAZORATINI TEKSHIRISH USULLARINI TAHLIL QILISH JARAYONLARINI TAKOMILLASHTIRISH. Oriental INTERNATIONAL JOURNAL OF SCIENTIFIC RESEARCHERS www.wordlyknowledge.uz Volume: 2, Issue: 1, 2023 157 renaissance: Innovative, educational, natural and social sciences, 1(10), 124-135.
Jalilov Rakhimjon Ravshanbek o’g’li. "CLADDING TILE PRODUCTION USING MAGNESIUM OXYCHLORIDE CEMENT MORTAR IMPROVED BY DIFFERENT WASTES." Gospodarka i Innowacje. 35 (2023): 276-278.
Jalilov Rahimjon Ravshanbek o’g’li. "Study of Morphology and Dimensions of Ultra-Dispersed Powders of Tungsten." American Journal of Social and Humanitarian Research 3.5 (2022): 20-22.
